Lithium-ion Dry Room Zones Explained

By November 3, 2026News

Why Each Zone Has Its Own Dewpoint

Lithium-ion dry rooms divide production into zones because each stage of cell manufacture tolerates moisture differently. Each zone can therefore run to its own dewpoint target, often called a tier, instead of requiring the entire facility to operate at the driest possible condition.

This post explains the main zones, why their dewpoint targets differ and how to measure conditions accurately in each area.

Why lithium-ion dry rooms are split into zones

Moisture threatens lithium-ion cells in different ways at each production stage. Before operators introduce electrolyte, water vapour can react with the surface of high nickel cathode materials and contribute to residual lithium compounds such as lithium hydroxide (LiOH) and lithium carbonate (Li₂CO₃). Electrodes and separators can also adsorb moisture, which the cell may seal in during assembly.

Once electrolyte is present, trace water can react with the lithium hexafluorophosphate (LiPF₆) salt commonly used in liquid electrolytes. This decomposition pathway can produce hydrofluoric acid (HF), which may corrode cell components, damage electrode interfaces and contribute to capacity fade and rising impedance over life.

Argonne National Laboratory’s BatPaC cell assembly model uses a maximum dry room dewpoint of −40 °C, equivalent to approximately 130 ppm(v) water vapour at atmospheric pressure. More sensitive steps, particularly electrolyte filling, often require much drier conditions.

Producing drier air costs more. Holding a space at −60 °C requires substantially more dehumidification and desiccant regeneration energy than holding it at −35 °C. Running the whole plant at the driest specification would therefore waste energy and add unnecessary cost. Instead, each zone controls its dewpoint to match the moisture sensitivity of the process inside it.

The main lithium-ion dry room zones

Coating and calendering

Operators coat electrodes with a slurry, dry them and then calender them, pressing them between rollers to set thickness and density. High nickel cathode materials readily absorb moisture, which can increase residual lithium content.

In some slurries, absorbed moisture raises viscosity or contributes to gelation, affecting coating quality and process stability. Once operators dry the electrodes, they must keep them dry until cell assembly.

Stacking or winding

Operators layer or wind electrode sheets with separators to form the cell structure. At this stage, the cell remains open to the dry room atmosphere, so electrodes and separators continue to adsorb moisture.

Any water the materials pick up here can enter the sealed cell and later interact with the electrolyte. This makes stacking and winding more moisture critical than general electrode handling.

Electrolyte filling and sealing

Electrolyte filling is usually one of the driest and most tightly controlled areas of the plant. The open cell and electrolyte face the room atmosphere directly, so operators must continuously control and measure the dewpoint.

Dewpoint measurement confirms the condition of the atmosphere surrounding the electrolyte and open cell. It does not measure the electrolyte’s water content; laboratories use Karl Fischer titration to measure a liquid sample.

Airlocks and material transfer areas

Personnel movement, material transfer and door openings introduce major moisture loads into a dry room. Plants therefore often monitor airlocks between zones separately and carry out spot checks.

See our post on dry room airlock moisture control.

Typical dewpoint tiers

Dewpoint targets vary with cell chemistry, process step, cell design, throughput and plant layout. The following ranges are indicative rather than universal specifications.

Zone Typical Dewpoint Approximate Moisture Level at 1 atm
Coating, calendering and general electrode handling −30 °C to −40 °C Approximately 380 to 130 ppm(v)
General cell assembly, stacking and winding −40 °C to −50 °C Approximately 130 to 39 ppm(v)
Electrolyte filling and sealing −50 °C to −60 °C or lower Approximately 39 to 11 ppm(v) or less

These conversions are approximate because dewpoint to ppm(v) conversion depends on pressure; at atmospheric pressure, −40 °C corresponds to roughly 127 ppm(v). For high nickel chemistries, solid state development lines or lithium metal systems, some areas may require even lower dewpoints.

No single published regulation sets one dewpoint limit for all lithium-ion battery manufacture. Cell and process engineering teams set the correct target against active material, electrolyte and finished cell moisture specifications.

Measuring each zone

A reading at the dehumidifier supply cannot show whether an individual production zone meets its specification. Plants install fixed dewpoint transmitters in each zone to show the conditions that zone is actually maintaining.

Place sensors close to the process but away from supply diffusers, doors and other local disturbance sources, so they measure the air to which the product is exposed. Engineers can use a portable hygrometer to verify fixed instruments, investigate excursions and trace a moisture problem back to its source.

Our application note, The importance of dewpoint measurement in lithium-ion battery manufacture, explains moisture mechanisms and recommended measurement locations in more detail.

If you would like help selecting instruments for each zone of your dry room, get in touch with our team.